| Processor |
| |
CPU |
32-bit Motorola 5407
ColdFire® Processor |
| |
Processing Speed |
257 MIPS (Dhrystone
2.1 benchmark) |
| Memory |
| |
On-board Memory |
36MB |
| |
Expandable Memory |
Compact Flash slot up
to 4GB (accepts standard Type II Compact Flash or IBM Microdrive®
not included) |
| Y-Bus |
| |
40 Mb/s parallel
communications; built-in 3-slot card cage supports Crestron's
existing CNX expansion cards and new C2 expansion cards |
| |
IR/Serial ports |
8 programmable
simultaneous outputs for IR, TTL Level RS-232 or serial interface;
signal (ws) and ground (G) pins; infrared output up to 1.2MHz with
individual UART per port allowing simultaneous firing of all ports |
| |
I/O Versiports |
(8) programmable
digital/analog input and digitaloutputs; digital outputs offer
250mA sync from maximum 24VDC; catchdiodes for use with real world
loads; digital inputs rated for 0-24VDC, 20K ohms input impedance,
logic threshold 1.25VDC; analog inputsrated 0-10VDC, protected to
24VDC maximum, 20K ohms input impedance; programmable 2K ohms
pullup resistor (per pin, software reference to GND or closure to
GND) |
| |
Communication ports |
6 bi-directional ports
for RS-232/422/485; Ports 3-6 Cresnet Accelerator ready |
| |
Computer console |
1 RS-232 port
(accessible from front or rear panel), 9-pin DB9 for programming
with a PC |
| |
Cresnet port |
1 4-pin male
connector, expandable via Cresnet Accelerator, which increases the
effective network speed, fan-out and device addresses by a factor
of 8 for each poll accelerator added to the system. |
| |
Relay ports |
(8) normally open,
isolated relays; each relay is rated 1A, 30VAC/DC; MOV arc
suppression across contacts for use with "real world"
loads |
| Z-Bus |
| |
300Mb/s parallel
communications; 1 expansion card slot. Optional cards include:
C2ENET-1: Single Port 10/100 BaseT Ethernet, C2ENET-2: Dual Port
WAN-LAN-10/100 BaseT Ethernet. Future Support for USB, USBII,
FireWire. |
| |
Ethernet Support |
10/100 BaseT
Ethernet, Dynamic/static IP and full duplex TCP/IP, UDP/IP,
Built-in Firewall, Built-in Router, Built-in Network Address
Translator (NAT), Built-in Web Server: Files shared in internal
flash or compact flash card memory (capabilities depending upon
which Z-Bus card is installed) |
| Operating System |
| |
Real-time, preemptive,
multitasking kernel, Multi-threaded, FAT32 file system with long
names, Fully compatible with existing SIMPL™ Windows® and SIMPL+™
programs, Enhanced SIMPL+ instruction set |
| Screen |
| |
Reverse mode (yellow
and black) LCD back light; 2 lines, 40 characters per line |
| Menu Function Buttons |
| |
PANEL |
Programmable interface
offering command text, indirect text, and hierarchical screen
structure |
| |
INFO |
Displays system
information including the loaded SIMPL program |
| |
MSG |
Displays system alarms
and error messages |
| |
TIME |
Permits alterations
to system date and time; access code required |
| |
COM |
Monitors the
transmission and reception traffic on each COM port |
| Menu Selection Buttons |
| |
MENU |
Returns screen display
to menu default state |
| |
^ |
Advances the current
screen display |
| |
V |
Returns the current
screen display to its previous state |
| |
BKLT |
Alters screen and LCD
brightness |
| Reset Buttons |
| |
HW-R |
Performs physical
reset of system |
| |
SW-R |
Restarts SIMPL
program |
| LED Indicators |
| |
PWR |
Indicates power
supplied to the unit |
| |
NET |
Indicates activity
within the system |
| |
ERR |
Indicates an error
message is available from the software feature buttons |
| |
LNK A |
Indicates attachment
to LAN (port 1 of Z-Bus card) |
| |
ACT A |
Indicates
communication over LAN (port 1 of Z-Bus card) |
| |
LNK B |
Indicates attachment
to LAN (port 2 of Z-Bus card, if dual port card inserted) |
| |
ACT B |
Indicates
communication over LAN (port 2 of Z-Bus card, if dual port card
inserted) |
| |
COM TXD (A-F) |
Indicates
transmission of data to serial devices attached to respective COM
ports |
| |
COM RXD (A-F) |
Indicates reception of
data from serial devices attached to respective COM ports |
| |
COM RTS (A-F) |
Indicates when unit
is ready to receive data from serial devices attached to
respective COM ports |
| |
COM CTS (A-F) |
Indicates when serial
device on the respective COM port is ready to accept data from the
unit |
| |
IR-SERIAL (A-H) |
Indicates activity on
respective IR/SERIAL line |
| |
INPUT-OUTPUT (1-8) |
Indicates input
voltage threshold for respective I/O port exceeded |
| |
RELAY (1-8) |
Indicates respective
relay is closed |
| |
SLOT (1-3) |
Illuminates when card
is inserted into slot; flashes when card is active |
| Power Requirements |
| |
100-250VAC, 2.3A,
50/60Hz, internal universal 75W power supply. Depending on the
expansion slot load, there is a 50W maximum load rating |
| Dimensions |
| |
3.47" / 8.81cm
(H) x
19.00" / 48.26cm (W) x
9.7" / 24.6cm (D) |
| Weight |
| |
7.25lbs (3.3kg) |
| Optional Accessories |
| |
C2N-NPA8 |
Allows a large number
of Cresnet devices to be controlled by a single PRO2 while
maintaining a high level of reliability and performance.
Connecting to the control processor via a high-speed RS-232 (using
built-in COM ports 3-6) or Ethernet link, it effectively
multiplies Cresnet bandwidth by implementing eight simultaneous
Cresnet networks, each operating at full speed. Multiple units can
be used at the same time for even larger or faster systems. |
| |
C2ENET-1 |
Single port ethernet
card |
| |
C2ENET-2 |
Dual port ethernet
card |